Mec shot manufacture full floor recovery system. The system is with low maintenance cost and easy to operate. The Pneumatic Cylinder operates the sweeping arms to push forward the falling media in the floor of the Blast Room through the Grating during Blasting Operation.

The pushed media falls in the cross screw trunk & transferred in the boot of the Bucket Elevator. From elevated buckets the media will get air washed, separating fine dust from re-usable before transferring in to Blasting machines for re-use.

In the present industrial scenario for the strict implementation of pollution control norms & OSHA standards for Sound, Air & Water, MEC SHOT has developed new Blast Room systems to meet the International standards of the blasting sound level.

The room panels are duly fabricated of Mild Steel & reinforced. The room walls are filled with mineral wool and covered with GI sheets to damper the sound. The sound level can be damper upto 40-50 dBA.

Mec shot blasting equipments are known for their quality, durability, low maintenance and productive in the field of Surface preparation. Mec shot manufactures the stationary bulk blasting equipment and the multi-outlet with grit valve /Thomson valve abrasive control systems. It allows each operator independent control of his abrasive media flow. Mec shot can also design and manufacture a system to meet customers specific needs.

The Grit valve / Thomson valve, the most precise metering valve available. It uses disposable abrasive and increases production. The remote control Valve cut off system in operator hand is one of the special features available.

The defects are generated during hot rolling of stainless steel flats and are forming of oxide layers, folding of edges & air traps on the edges of the flats in manufacturing process. The defect becomes prominent on final product during reduction in stainless steel sheet.

MEC SHOT has developed air operated blasting machine for removing the defects on the edge of the stainless steel flat.

The flats are loaded on the roller conveyor from one side of the special blasting machine and are off loaded from other side after being blast cleaning automatically.

The Valve Plates for compressors are blasted for the De-burring; De-scale by automatically on revolving Satellite over a Indexing Turn Table by Air Operated Blasting Machine.

MEC SHOT has developed automatic air operated blasting machine for the De-burring, De-scale of Valve Plates for Compressors for consistency in repeatability.

The plates are loaded/unloaded on revolving satellites mounted on Indexing Turn Table. The revolving Plates get blast cleaned by 2 nos. fixed guns. The unblasted surface is protected by masking plate, the abrasive get recycled automatically for continuously un-interrupted blasting operation. The dust generated during the blasting operation is trapped in dust collector & clean air is let out in atmosphere. Thus keeping the environment eco-friendly.

MEC SHOT has successfully engineered and supplied Vapour Cleaning Machines for cleaning of Aero Engine Parts without dimensional variation.

The supplied machine works on Suction Induction Principle of Abrasive Blasting. The fine particles of Glass Bead as an abrasive are suspended in liquid [usually water] and are then pumped into the nozzle as slurry. At nozzle, slurry is induced with air stream and propelled against Aero Engine Parts.

The equipment consists of Wet Blasting Cabinet SS Fabricated to prevent Rusting, Blasting Nozzle with Glandless Pump for slurry feeding, Mist Collector and necessary Controls. Rotary Turntable with work car mounted track extension & Blasting Gun is provided. A glandless slurry pump is used to feed the slurry at positive pressure into the blast gun. The operator places the job on rotary turn table. The work car mounted turntable carries it into the blast chamber where the turntable starts rotating. As the job rotates, Blast Gun which is either fixed or manures manually clean the Aero Engine Parts. The operator simply loads and unload the job from turntable. The mist generated during blasting operation is sucked into a mist collector keeping the vision clear.

MEC SHOT Semi Automatic Blasting Machine Model : SB-SP2 To blast clean forged steel components (Splined Shaft For Automobile) for surface preparation before nylon powder coating.

The offered Model SB-SP2 operates on the suction principle of abrasive blasting. The vacuum created by the compressed air issuing out of an injector lifts the abrasive from storage tank to the nozzle in the blast guns. The lifted abrasive gets mixed with the compressed air in the blast guns to strike the job to be cleaned. The operator places the job on satellite. As job rotates, blast guns Pneumatically reciprocates vertically along the job, thus cleaning its outer periphery. After cleaning the job get air washed before being lifted by the operator.

Used abrasive and dust created during blasting are sucked through a flexible suction hose to reclaimer, where usable grit is reclaimed and collected in a storage tank for recycling and the dust generated during the blasting operation is trapped in dust collector & clean air is let out in atmosphere.

MEC SHOT has developed manufacturer, installed & commission (in progress) a fabricated blast room for Robotic Laser Operations on the parts of power generating units. During the laser caddling operation mist mixed particles are sucked through the suction hood and exhausted out to the exhaust fan.

Special anti glare viewing window have been provided as a protection for the outside viewing during robotic laser operation.

A Pressure Feed Hopper has been developed & designed for the Seed Industry. Seeds or powder dust is being fed from lower Pressure Feed Hopper to high store Silo by pneumatic pressure for storage.

The operator places the job on turn table mounted on work car. Track extension will be provided for inside / outside movement of work car. The work car is pushed manually inside the cabinet. The operator cleans the job by manual movement of the gun through hand holes provided on the front of the cabinet. A spring is provided for holding the gun arrangement to avoid the operator’s fatigue. A foot switch is also provided for On/Off of blasting operation.

Used abrasive falls directly into the cabinet hopper for subsequent feeding to blast generator. The dust created inside the cabinet is sucked through suction hose and carried into the fabric bag dust collector [due to suction created by exhaust fan motor] and deposit inside the fabric bag and clean air is exhausted into the atmosphere to keep the environment clean and friendly.

MEC SHOT Semi Automatic Blasting Machine Model : SB-SP4 To blast clean Aluminum Casted Door Handles and Lock Strips to achieve matt & decorative finish.

The machine operates on the suction principle of abrasive blasting. The vacuum created by the compressed air issuing out of an injector lifts the abrasive from storage tank to the nozzle in the blast guns. The lifted abrasive gets mixed with the compressed air in the blast guns to strike the job to be cleaned. The operator places the job on satellite. As job rotates, blast guns Pneumatically reciprocates horizontally along the job. After blasting the job get air washed before being lifted by the operator.

Used abrasive and dust created during blasting are sucked through a flexible suction hose to reclaimer, where usable grit is reclaimed and collected in a storage tank for recycling and the dust get trapped in filter bags of dust collector. Operator has only to load and unload the job on and from the satellite.

MEC SHOT Semi Automatic Blasting Machine Model : SB-806060 special to remove burrs & blast clean Hypodermic Needles during manufacturing.

The machine operates on the suction principle of abrasive blasting. The vacuum created by the compressed air issuing out of an injector lifts the abrasive from storage tank to the nozzle in the blast guns. The lifted abrasive gets mixed with the compressed air in the blast guns to strike the tip of the Needles to remove burrs. The operator places the job on a stand. As job fixed, blast gun Pneumatically reciprocates horizontally along the job. After blasting the job get air washed before being lifted by the operator.

Used abrasive and dust created during blasting are sucked through a flexible suction hose to reclaimer, where usable grit is reclaimed and collected in a storage tank for recycling and the dust get trapped in filter bags of dust collector. Operator has only to load and unload the job from the stand.

To Paint the surface in a Vertical Down Draft Dry Type Paint Booth System (Size 10 meter Length, 6 meter Width & 6 meter Height) is to paint the Thermal Turbine Structures. This system is with Air inlet Filter & Paint Trap Filters for Pollution Free Operation.

A Tunnel Type Airless Shot Blasting Machine with passage opening 1200 x 300 mm (H) suitable for cleaning of sheet and structural etc. with four blast wheel station. Reverse Pulsejet Dust Collector, Control Panel and with roller Conveyor for job conveying.